Design, Fabrication and Analysis of Material Requirements of Spices Mixing Machine

Rozi Saferi, Asmara Yanto, Jendri Surianda

Abstract


The process of mixing the spices often done manually, which it takes time and reduces the effectiveness of the process. This study aims to analyze the design, material requirements and production process of a spices mixer machine. In this work is also done to analyze the speed optimization in mixing process of spices with the main food. Analysis of the machine design using the finite element method by aided Autodesk Inventor software. The analysis results show that the mass density of the frame is 8.8041 g/cm3, and the maximum compressive strength is 345 MPa. Furthermore, the young’s modulus is 200 GPa, the position ratio is 0.3 and the shear modulus is 76.9231 GPa. The test of spices mixer machine showed that the optimal spice stirring value occurred at 35 rpm with a mixing percentage of 83%.The process of mixing the spices often done manually, which it takes time and reduces the effectiveness of the process. This study aims to analyze the design, material requirements and production process of a spices mixer machine. In this work is also done to analyze the speed optimization in mixing process of spices with the main food. Analysis of the machine design using the finite element method by aided Autodesk Inventor software. The analysis results show that the mass density of the frame is 8.8041 g/cm3, and the maximum compressive strength is 345 MPa. Furthermore, the young’s modulus is 200 GPa, the position ratio is 0.3 and the shear modulus is 76.9231 GPa. The test of spices mixer machine showed that the optimal spice stirring value occurred at 35 rpm with a mixing percentage of 83%.

Keywords


spices mixing machine, design, finite element method, material requirements, speed optimization.

Full Text:

PDF

References


Aditya, 2017. “Perencanaan Mesin Pencampur Bumbu Kripik Singkong Dengan Kapasitas 40 Kg/Jam.” Artikel 01(11): 1–9.

A. Yaqin, 2015. “Analisis Kebutuhan Material Dan Jenis Proses Produksi Berdasarkan Desain Peniris Dan Pencampur Bumbu.” Teknik Mesin 03: 63–68.

E.A. Yuser. 2016. “Pengujian Mesin Pengaduk Bumbu Keripik.”

Laina, 2019. “Desain dan Analisis Kekuatan Rangka Tempat Sampah di Balai LAPAN Garut Menggunakan Metode Elemen Hingga Balai Uji Teknologi dan Pengamatan Antariksa.”

Pratama, 2013. “Simulasi Pembuatan Dan Analisis Chasing Powerbnk Berbasis Autodesk Inventor 3D.” Teknik Mesin: 1–7.

Ramadhani, 2018. “Perancangan Dan Analisis Struktur Mekanik Prototipe Laser Cutting.” 05(1): 2–6.

Sularso dan S. Kyokatsu. 1980. Dasar Perencanaan dan Pemilihan Elemen Mesin. Jakarta. Pradya pramita

D. Widya, 2014. “Hands On Autodesk Inventor 2014.” Artikel: 38.

A. Yanto dan A. Anrinal, “Studi Getaran Eksperimental Akibat Kelonggaran Sistem Transmisi Sabuk Pada Mesin Rotari,” Prosiding Seminar Nasional: Peranan Ipteks Menuju Industri Masa Depan (PIMIMD), 2017, pp. 40-46.

A. Yanto, Z. Abidin, A. Anrinal and R. Saferi, “An Approach for The Condition Monitoring of Rotating Machinery,” in Proc. The First International Conference on Technology, Innovation, and Society (ICTIS), 2016, pp. 219-224.


Refbacks

  • There are currently no refbacks.


Copyright of JTM (p-ISSN: 2089-4880   e-ISSN:2598-8263)