Track Record and Research Challenges of Automotive Vocational Lecturer in Indonesia: Screening from Google Scholar 2016-2018

Bagiyo Condro Purnomo, Muhammad Latifur Rochman, Muji Setiyo

Abstract


This article presents a research review of automotive vocational lecturers in Indonesia obtained from Google Scholar during 2016-2018. We found more than 500 articles on Google Scholar produced by 277 lecturers from automotive vocational programs. However, through data filtering, there are only 208 publications related to automotive, including the development of learning media in VHE. Looking at the world automotive research trend (which leads to major issues regarding battery systems, downsizing and turbocharging, and advanced combustion modes), and with concerns about the availability of fossil energy, major and fundamental reforms are needed for research activities in automotive vocational lecturers in Indonesia, both in terms of topic and depth of research material. As a recommendation, stakeholders in automotive vocational programs in universities should immediately form a research roadmap together and form a national automotive research consortium in order to contribute in realizing environmentally friendly vehicle technology and a sustainable national transportation system.


Keywords


Research trend, Vocational automotive lecturer, Google scholar

Full Text:

PDF

References


A. Oktav, “New Trends and Recent Developments in Automotive Engineering,” in Researches on Science and Art in 21st Century Turkey, A. A. asan Arapgirlioğlu, Robert L. Elliott, Edward Turgeon, Ed. Gece Kitaplığı, 2017.

Argonne National Laboratory, “Advanced Vehicle Technologies,” Energy Systems. [Online]. Available: http://www.anl.gov/energy-systems/group/advanced-vehicle-technologies. [Accessed: 04-Mar-2018].

EIA, “Global Transportation Energy Consumption: Examination of Scenarios to 2040 using ITEDD,” Washington DC, 2017.

R. . Colvile, E. . Hutchinson, J. . Mindell, and R. . Warren, “The transport sector as a source of air pollution,” Atmospheric Environment, vol. 35, no. 9, pp. 1537–1565, Mar. 2001.

U. Eberle, B. M€uller, and R. von Helmolt, “Fuel cell electric vehicles and hydrogen infrastructure : status 2012,” Energy & Environmental Science, vol. 5, pp. 8780–8798, 2012.

Jess Staufenberg, “Norway to ‘completely ban petrol powered cars by 2025,’” Independent, 2016. [Online]. Available: https://www.independent.co.uk/. [Accessed: 24-May-2019].

Environews, “Carbon neutrality: France sets 2040 date to phase out fossil-fuel-powered vehicles,” 2017. [Online]. Available: http://www.environewsnigeria.com. [Accessed: 24-May-2019].

WLPGA, Guide to new autogas markets: A step-by-step approach to introducing LPG use for transport based on lessons learned from successful markets. Neuilly-sur-Seine: WLPGA, 2018.

I. C. Setiawan, “Policy Simulation of Electricity-Based Vehicle Utilization in Indonesia (Electrified Vehicle - HEV, PHEV, BEV and FCEV),” Automotive Experiences, vol. 2, no. 1, pp. 1–8, 2019.

C. Clay, “Natural Gas Vehicles: Opportunities and Challenges in the Transportation Sector.” Drive Natural Gas Initiative, Washington D.C., pp. 1–19, 2012.

Peraturan Menteri Perindustrian Republik Indonesia Nomor 33/M-IND/PER/7/2013 tentang Pengemabangan Produksi Kendaraan Bermotor Roda Empat yang Hemat Energi dan Harga Terjangkau. Indonesia, 2013.

Gaikindo, “Indonesia Automotive Industry Report on 2013 Auto Market,” in The 20th APEC Automotive Dialogue, 2014, no. April.

Kementerian ESDM Republik Indonesia, “Blueprint Pengelolaan Energi Nasional 2006-2025.” Jakarta, 2006.

D. S. Saputri, “2025, Menperin Target 20 Persen Produksi Kendaraan Listrik,” Republika Online, 2019. [Online]. Available: https://www.republika.co.id/. [Accessed: 24-May-2019].

H. Purwono and R. Rasma, “Analisis Kebocoran Air Pendingin Dari Radiator Pada Bulldozer Tipe D375A-5,” Prosiding Semnastek, 2018.

V. A. T. Manurung, Y. T. Joko, and R. I. Poetra, “Auto Drain Valve Water Separator inside the Unit of Komatsu HD 465-7R,” in IOP Conf. Series: Materials Science and Engineering, 2018, pp. 0–5.

H. Purwono, “Perancangan Special Tool Remove And Install Hoist Cylinder Pada Unit Dump Truck HD 1500-7,” in Prosiding Semnastek, 2018, pp. 1–10.

I. K. Nugraheni, Triyono, W. Trisunaryanti, Nuryati, and A. Angkasa, “Physical Properties of Palm Oil Mill Effluent Trans- esterification with Local Zeolite,” in AIP Conference Proceedings, 2018, no. November.

Y. Yuhelson, P. Prasetya, and J. Lukman, “Test of Biodiesel Usage to Engine Performa on Dong Feng Diesel with Power 7 HP,” Prosiding CELSciTech, 2018.

R. M. Susanto and M. Setiyo, “Natural Gas Vehicle (NGV): Status Teknologi dan Peluang Pengembangannya,” Automotive Experiences, vol. 1, no. 01, pp. 1–6, 2018.

I. Yamin, B. Sugiarto, S. Abikusna, and D. Suntoro, “The use of low grade bio ethanol as fuel mixer in gasoline engine with optimization compact distillator,” in E3S Web of Conferences, 2018.

S. Abikusna, B. Sugiarto, and R. Monasari, “Utilization distillate low grade bioethanol as fuel mixing on SI engine (from carburetor to injection),” AIP Conference Proceedings, 2018.

M. Setiyo, Saifudin, A. W. Jamin, R. Nugroho, and D. W. Karmiadji, “The Effect of Ethanol on Fuel Tank Corrosion Rate,” Jurnal Teknologi, vol. 80, no. 6, pp. 19–25, 2018.

B. Waluyo, I. N. G. Wardana, L. Yuliati, and M. N. Sasongko, “The role of molecule cluster on the azeotrope and boiling points of isooctane-ethanol blend,” Fuel, vol. 215, no. September 2017, pp. 178–186, 2018.

R. Monasari, S. Abikusna, B. Sugiarto, and B. Ajiseno, “Analysis of emission gas and fuel consumption on SI engine fueled with low-grade bioethanol and oxygenated cycloheptanol additive,” in IOP Conf. Series: Earth and Environmental Science, 2018.

S. Abikusna, B. Sugiarto, R. Monasari, R. Aditya, and D. Hendrawan, “Performance analysis (WHP and torque) on SI engine fueled with low- grade bioethanol and oxygenated fuel additive,” in IOP Conf. Series: Earth and Environmental Science, 2018.

I. K. Nugerahen and M. M. A. Pratama, “Pengukuran Penggunaan Bahan Bakar Biofuel (Premium Dan Bioetanol) Terhadap Kinerja Mesin Bensin 4 Tak,” Elemen, vol. 5, no. 1, pp. 1–6, 2018.

I. Yuwono and A. C. Arifin, “Studi Eksperimen Rekayasa ECU Pada Sepeda Motor untuk Pemakaian Bahan Bakar Etanol 95 Persen,” Journal of Electrical Electronic Control and Automotive Engineering (JEECAE), vol. 3, no. 2, pp. 195–198, 2018.

J. Tokuda, S. Mukasa, H. Tanaka, I. Rahim, and S. Nomura, “Characteristic Of Argon Plasma Jet From Methane Hydrate Decomposition For Hydrogen Production,” in International Heat Transfer Conference, 2018.

Raji and Jusnita, “Hidrogen sebagai penghemat bahan bakar pada sepeda motor matic,” in Simposium Nasional Teknologi Terapan (SNTT) V, 2018.

M. Setiyo, B. C. Purnomo, B. Waluyo, D. R. B. Syaka, and N. Hamidi, “Refrigeration effect and energy efficiency ratio (EER) calculation of 1/2 cycle refrigeration system on LPG-fueled vehicles,” in IOP Conf. Series: Materials Science and Engineering, 2018.

M. Setiyo, B. Waluyo, Ba. C. Purnomo, D. W. Karmiadji, and I. C. Setiawan, “Potential of ½ cycle refrigeration system for food transport application,” in IOP Conf. Series: Materials Science and Engineering, 2018.

B. A. Prasetyo, D. A. Rizani, M. Setiyo, N. Widodo, Saifudin, and B. C. Purnomo, “Estimasi Pemborosan Bahan Bakar Akibat Kemacetan Menggunakan Analisis Citra Google Map (Studi Kasus pada Simpang Armada Town Square Mall Magelang),” Automotive Experiences, vol. 1, no. 02, pp. 36–42, 2018.

I. Hasan, Erwin, A. K. Junaidi, and D. S. Arief, “Traffic Noise Impact in Perspective of City Ecology,” Journal of Aeronautical, vol. 14, no. 2014, pp. 1–4, 2018.

M. H. Anshari, K. D. Artika, and A. Kuswoyo, “Analisa Pengukuran Tingkat Kebisingan Sepeda Motor Berdasarkan Rpm Dan Jumlah Kendaraan,” Elemen, vol. 5, no. 1, pp. 7–10, 2018.

V. A. T. Manurung and K. Anam, “Menurunkan Kerusakan Yang Tidak Terjadwal (Unschedule Breakdown) Sistem Transmisi Motor Grader Komatsu Tipe GD 825A-2 Di PT Pamapersada Distric Adaro,” TECHNOLOGIC, vol. 9, no. 1, 2018.

V. A. T. Manurung and Setiawan, “Oil Flushing Method To Avoid Unschedule Breakdown Final Drive Components At Komatsu Dump Hd465-7r In Pt Atp,” in ICETASIA, 2018.

B. W. Suroto Munahar, Bagiyo Condro Purnomo, Muji Setyo, “Peningkatan Pengelolaan Unit Usaha Bengkel Kampus Dengan Penguatan Manajerial,” Dianmas, vol. 7, no. 1, pp. 59–68, 2018.

A. Fiatno, D. Jumali, and Misrianto, “Penerapan Realibility Centered MAintenance (RCM) pada Poros Depan Isuzu Type CXZ-51,” Jurnal Teknik Industri Terintegrasi, vol. 1, no. 1, pp. 9–14, 2018.

L. S. H. Wakhinuddin and T. Sugiarto, “Faktor-Faktor Yang Mempengaruhi Tindakan Tidak Aman Pada Mekanik Bengkel Toyota Di Kota Padang Tahun 2017,” Automotive Engineering Education Journal, vol. 1, no. 1, 2018.

M. A. S. Mandra, Saharuna, and H. A. Gani, “Peningkatan pengetahuan dan keterampilan penggunaan Engine Scanner pada mekanik bengkel mobil di Kabupaten Wajo,” in Prosiding Seminar Nasional Lembaga Pengabdian Kepada Masyarakat Universitas Negeri Makassar, 2018, no. 1, pp. 530–532.

Tafakur and M. Solihin, “Electronic Spark Advance Ignition System Simulator As Instructional Media For Assisting Electrical Practices On Automotive Field,” VANOS Journal of Mechanical Engineering Education, vol. 3, no. 1, 2018.

M. Raybian Nur, “Media Pembelajaran Pelepasan Panas Menggunakan Radiator Motor Dengan Variasi Kipas Dan Kecepatan Kipas,” PolhaSains, vol. 06, no. 2, pp. 2–6, 2018.

W. Yahya, “Desain Media Pembelajaran Sistem Kontrol Elektropneumatik Berbasis Programmable Logic Controller,” Jupiter (Jurnal Pendidikan Teknik Elektro), vol. 3, no. 1, p. 42, 2018.

H. Nasrullah, “Pembuatan dan Pengujian Media Pembelajaran K3 (Keselamatan (Keselamatan dan Kesehatan Kerja) Berbasis Android,” Automotive Experiences, vol. 1, no. 02, pp. 53–57, 2018.

R. Syahyuniar, Y. Ningsih, and R. D. Kurniawan, “Perancangan Sistem Kerja Simulator AC (Air Conditioner) Mobil,” Jurnal Elemen, vol. 5, no. 1, p. 20, 2018.

I. Y. Basri, A. Arsyfadhillah, D. Irfan, and T. Thamrin, “Rancang Bangun Media Pembelajaran Mini Trainer IC 555,” INVOTEK: Jurnal Inovasi Vokasional dan Teknologi, vol. 18, no. 2, pp. 65–76, 2018.

W. Purwanto, T. Sugiarto, A. Baharudin, D. S. Putra, and N. Hidayat, “The Design And Development Of Voltage Amplifiers Using Microcontroller For Mass Absolute Pressure (MAP) Sensor In The Toyota Avanza,” VANOS Journal of Mechanical Engineering Education, vol. 3, no. 2, 2018.

F. Majedi, F. Susanto, A. T. Hardiyanto, and T. Hardiyanto, “Penerapan Sistem Alternating Current Generator (Acg) Pada Motor Bensin mattrix Gasoline Engine Cx200,” Jurnal Teknologi Terpadu, vol. 6, no. 1, pp. 77–81, 2018.

E. Tarigan, “Studi Kasus: Karakteristik Konsumsi Bahan Bakar Sepeda Motor 110 CC Matic dengan CDI BRT,” Automotive Experiences, vol. 1, no. 02, pp. 53–57, 2018.

R. S. Maryati and M. F. Jauhari, “Manual Select Switch Mode Untuk Penanganan Diagnosis Trouble Code Pada Sistem Injeksi Sepeda Motor Suzuki,” in Prosiding SNRT (Seminar Nasional Riset Terapan) Politeknik, 2018, no. November, pp. 71–78.

T. Sugiarto, D. S. Putra, W. Purwanto, and W. Wagino, “Analisis Perubahan Output Sensor Terhadap Kerja Aktuator pada Sistem EFI (Electronic Fuel Injection),” INVOTEK: Jurnal Inovasi Vokasional dan Teknologi, vol. 18, no. 2, pp. 91–100, 2018.

Novendra, R. Lapisa, and T. Sugiarto, “Analisis Perbandingan Kekerasan Baja Pada Sproket Depan Dan Belakang Sepeda Motor Supra X 125 Hardening Dengan Menggunakan Media Pendinginan Yang Bervariasi,” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

A. Burhanudin, B. Septian, B. Waluyo, and Saifudin, “Investigasi Kesalahan Pembacaan Display Konsumsi Bahan Bakar Pembacaan Display Konsumsi Bahan Bakar pada Mobil Datsun Go,” Automotive Experiences, vol. 1, no. 02, pp. 53–57, 2018.

M. Setiyo, S. Soeparman, S. Wahyudi, and N. Hamidi, “The Alternative Way to Drive the Automobile Air-Conditioning, Improve Performance, and Mitigate the High Temperature: A Literature Overview,” Periodica Polytechnica Transportation Engineering, vol. 46, no. 1, pp. 36–41, 2018.

M. Luthfi, D. Ahmad, M. Setiyo, and S. Munahar, “Uji Komposisi Bahan Bakar dan Emisi Pembakaran Pertalite dan Premium,” Jurnal Teknologi, vol. 10, no. 1, pp. 67–72, 2018.

Listiyono, “Optimization of Material Variations and Installation Angle Catalytic Converter in Muffler to Emission Gas,” Journal of Information Engineering and Applications, vol. 8, no. 2, pp. 13–20, 2018.

A. Kurniawan, Martias, and I. Y. Basri, “Pengaruh Penggunaan Pulsed Secondary Air Injection System (PAIR) Terhadap Emisi Gas Buang Karbon Monoksida (CO) Dan Hidro Karbon (HC) Pada Sepeda Motor Suzuki Satria F 150 cc,” Automotive Engineering Education Journal, vol. 2, no. 1, 2018.

H. Nurrohman, B. Susanto, and N. Widodo, “Studi Eksperimen Variasi Tekanan Bahan Bakar Terhadap Emisi pada Mesin EFI,” Automotive Experiences, vol. 1, no. 02, pp. 53–57, 2018.

M. Mardyaningsih and A. Leki, “Kajian Penggunaan Zeolit Alam Kabupaten Kupang Untuk Menurunkan Emisi Gas Buang Co dan HC Pada Motor Bensin 4 Silinder,” Jurnal Teknik Mesin, vol. 1, no. 1, pp. 1–10, 2018.

F. Majedi, F. Susanto, B. P. Sandy, and B. Wiratmoko, “Efek Perubahan Kapasitas Mesin dan Penggunaan 2 Busi pada Motor 4 Langkah terhadap BSFC dan Emisi Gas Buang,” Jurnal Teknologi Terpadu, vol. 6, no. 2, p. 115-, 2018.

A. Supriyanto, H. Maksum, and D. S. Putra, “Perbandingan Penggunaan Berbagai Jenis Bahan Bakar Terhadap Emisi Gas Buang Pada Sepeda Motor 4 Langkah,” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

M. Muhammad, B. Amin, and T. Sugiarto, “Pengaruh penggunaan katalis plat tembaga pada knalpot sepeda motor terhadap kandungan emisi karbon monoksida (co) dan hidrokarbon (hc),” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

W. Purwanto, T. Sugiarto, H. Maksum, D. S. Putra, and E. Alwi, “Comparison of Three Topologies Rotor to Improve Efficiency and Torque for High-Speed Spindle Motor Applications,” in 2018 International Conference on Applied Information Technology and Innovation (ICAITI, 2018, pp. 176–181.

W. Purwanto, D. S. Putra, and Risfendra, “Effect of Stator Slot Geometry on High Speed Spindle Motor Performance,” in 2018 International Conference on Information and Communications Technology (ICOIACT), 2018, pp. 560–564.

D. R. Putra, H. Maksum, and D. S. Putra, “Pengaruh perbandingan penggunaan roller racing dengan roller standard terhadap daya dan torsi pada motor matic,” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

A. Irawan and D. A. Tyagita, “Study Comparative Of Fuel Use Of LPG , Pertalite , And Pertamax On Engine Erformance Armfield Cm 11 Mk II,” in The First International Conference of Food and Agriculture, 2018, pp. 554–559.

S. K. Utama, Erzeddin Alwi, and Wagino, “Pengaruh variasi coil sistem pengapian suzuki satria fu 150 tahun 2012 terhadap torsi dan daya,” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

Y. R. Fauzi, “Pengaruh Penambahan Turbo Cyclone Aksial Terhadap Aliran Dan Performa Motor Bakar,” Turbo : Jurnal Program Studi Teknik Mesin, vol. 7, no. 1, pp. 25–31, 2018.

K. Supriadi, Wagino, and T. Sugiarto, “Pengaruh Variasi Oversize Piston Terhadap Konsumsi Bahan Bakar Yamaha Mio Sporty,” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

A. Robiul and A. Udin, “Test Characteristics of Two-Step Gasoline Engine with Fuel Mix Essential Oils and Aceton,” in The First International Conference of Food and Agriculture, 2018, pp. 478–485.

J. Effendi, H. Maksum, and T. Sugiarto, “Analisis Penggunaan Penstabil Tegangan (Voltage Stabilizer),” Automotive Engineering Education Journal, vol. 1, no. 2, 2018.

Nurhadi, “Pengembangan Sepeda Motor Listrik Sebagai Sarana Transportasi Ramah Lingkungan,” in Seminar Nasional Inovasi dan Aplikasi Teknologi di Industri 2018, 2018, pp. 249–255.

Arman and A. K. Muhammad, “Rancang Bangun Alat Ukur Emisi Gas Buang Yang Terintegrasi Komputer Untuk Kendaraan Ringan,” in Prosiding Seminar Hasil Penelitian (SNP2M) 2018 (pp.232-238), 2018, pp. 232–238.

H. Purwono and Rasma, “Perancangan Perkakas Untuk Melepaskan Dan Memasang Piston Steering Cylinder Pada Unit HD1500-7,” Jurnal Mesin Teknologi, vol. 12, no. 1, pp. 47–53, 2018.

Sudarmadji, B. S. A. Purwono, and Santoso, “Performance Evaluation Criterion of Nanofluid,” in Microfluidics and Nanofluidics and, M. S. Kandelousi, Ed. London: IntechOpen, 2018, pp. 277–292.

H. Fahrian, S. Munahar, and D. S. Putra, “PengembanganSirkuit Security System untuk Meningkatkan DriverBehaviour Control padaKendaraan,” Automotive Experiences, vol. 1, no. 1, pp. 13–19, 2018.

A. N. Miftachul and B. Waluyo, “Model Sistem Monitoring Minyak Pelumas Digital dengan Memanfaatkan Gaya Apung dengan Sensor Load Cell,” Automotive Experiences, vol. 1, no. 02, pp. 53–57, 2018.

G. M. Seprihadaniansyah, A. Kuswoyo, and M. Adriana, “Modifikasi Knalpot Menggunakan Katalitik Konverter Dan Arang Akasia Guna Mengurangi Emisi Gas Buang Kendaraan,” Jurnal Elemen, vol. 5, no. 1, pp. 11–19, 2018.

W. N. Farid Majedi, Indarto Yuwono, “Penggunaan Modul Thermoelectric (Elemen Peltier) Pada Sistem Pendingin Bahan Bakar Bensin,” Journal of Electrical, Electronics, Control, and Automotive Engineerin, vol. 3, no. 1, 2018.

B. C. Purnomo and B. H. Priyanto, “Kajian Pengaruh Perubahan Konsentrasi Refrigerant Musicool 134-CO2 Terhadap Performa Katup Ekspansi Tipe TEV,” Automotive Experiences, vol. 1, no. 02, pp. 53–57, 2018.

M. Crawford, “3 Emerging Trends in Automotive Engineering,” ASME, 2013. [Online]. Available: https://www.asme.org/engineering-topics/articles/automotive/3-emerging-trends-automotive-engineering. [Accessed: 25-May-2019].

Omic International, “Emerging Trends in Automotive Engineering,” 2019. [Online]. Available: https://www.omicsonline.org/conferences-list/emerging-trends-in-automotive-engineering. [Accessed: 25-May-2019].

Argone National Laboratory, “Energy System Division: Areas of Focus.” [Online]. Available: https://www.anl.gov/es/areas-of-focus. [Accessed: 25-May-2019].


Refbacks

  • There are currently no refbacks.


JTM Indexed by:

 
 

Copyright of JTM (p-ISSN: 2089-4880   e-ISSN:2598-8263)